Summary
Moisture content is the number that rarely makes it into a purchase order and most often gets blamed after delivery. It is not a fixed value. At the press it is set by the process; inside a container it follows the day-night temperature swing; in your warehouse it follows relative humidity; after cutting it keeps moving with the workshop air. This article follows one panel through seven stages, from fibre drying to arrival, showing where water is driven out and where it comes back. It explains why panels from the same batch arrive flat in one bundle and bowed in the next, why the EN 322 oven-dry method remains the only basis for arbitration, and why a hand-held meter is useful for comparison but not for pass or fail. It closes with three clauses worth writing into an order: a moisture range with a test method, packaging and transport requirements, and a re-test rule for arrival. The short version: after the press, moisture content mostly goes one way - up - and what arrives is half factory control and half packaging and shipping.

Figure 1: Within one batch, the top of the stack, the outer bundles and the centre of the stack do not change at the same rate. Acceptance is less about "what this panel reads" than "how much the stack varies".
1. Moisture content is a range, a method and a moment
Moisture content is defined on an oven-dry basis: the mass of water lost when a specimen is dried to constant mass, expressed as a percentage of the dry mass. EN 322 (wood-based panels - determination of moisture content) sets out that method. Three consequences follow, and all three are routinely ignored.
First, it describes one specimen at one moment. On a 1220 × 2440 panel, the edges and the centre, the face and the core, do not hold the same amount of water. A single reading does not represent a stack.
Second, it changes with time. The same panel has one value when it leaves the press, another after sanding, another when it is packed, and another after two weeks in your warehouse. The direction of change depends on whether the water vapour pressure in the surrounding air is above or below that of the panel.
Third, drier is not automatically better. A panel that is too dry will take up moisture once it reaches its service environment; one that is too wet will lose it after cutting, with consequences for coating and edge banding. What a factory controls is the gap between the shipping value and the destination environment, not the lowest possible number.
That is why "moisture content 8%" in a contract is almost unenforceable on its own. Four things are enforceable: a range, a sampling plan, a test method and a decision rule.
2. Seven stages: where water leaves, where it returns
|
Stage |
What happens to moisture |
Who controls it |
|
1 Fibre drying |
Hot air brings fibre moisture down to the process set point - the lowest point in the whole chain |
Dryer outlet temperature and airflow, residence time |
|
2 Resin blending |
The glue itself carries water; a higher spread brings more |
Resin type, spread rate, resin concentration |
|
3 Forming and pre-pressing |
The fibre mat is exposed to workshop air and either picks up or loses moisture |
Workshop climate, time between forming and pressing |
|
4 Hot pressing |
Heat turns water into steam and drives it out; the panel leaves the press with a dry face and a wetter core |
Press temperature curve, pressure, line speed |
|
5 Cooling and stacking |
The centre of a stack cools slowly and moisture redistributes within and between panels; wrap a warm stack and the vapour stays inside |
Cooling time, stacking pattern, ventilation |
|
6 Sanding and cutting |
The dense surface layer is removed, exposed area increases and uptake speeds up |
Time between sanding and packing, workshop humidity |
|
7 Packing and shipping |
Film and pallets keep some water out; the day-night temperature swing inside a container produces condensation, and that is where most returning water comes from |
Packaging, container loading, route and season |
Read the table downwards and one pattern appears: water is driven out in stages 1 to 4, and from stage 5 onwards it only comes back. What arrives is therefore decided half by the factory's shipping control and half by packaging and transport - and the second half is usually the thinnest section of the contract.
Pressing deserves one more sentence. When a panel leaves the press, the faces are already dry while steam is still moving out of the core. Pack it before it has cooled and that vapour is sealed inside the stack, where it condenses on the outermost panels. Open the bundle and the faces feel damp. This is not "the factory did not dry the fibre"; it is a gap between cooling and packing. For a claim, the two causes carry completely different responsibility, and an inspection has to tell them apart.
3. Same batch, some panels flat and some bowed
The immediate cause of bowing is not high moisture content. It is a difference in moisture content between the two faces.
Moisture on one face. That face swells while the other does not, and the panel becomes convex towards the wet face.
Drying on one face. That face shrinks, and the panel becomes concave towards the dry face - the edges lift.
Position in the stack. Outer, top and bottom panels move first; the centre lags. A single sample often comes from the most stable panel in the stack.
Stacking practice. Bearers spaced too far apart let the panel creep under its own weight; add moisture movement and the deflection becomes permanent. Stacks standing on the floor take moisture from below, creating a gradient in the opposite direction.
After cutting. Residual stress releases when the panel is cut, and narrow rails and frame parts show bow that a full sheet concealed. Many "it bowed as soon as we cut it" complaints were decided before cutting.
Standing storage. Leaning against a wall with too few supports and too much angle produces the same permanent set over time.
The diagnostic follows: look at differences, not averages. Between the two faces of one panel, between top, middle and bottom of one stack, between bundles of one batch. If the differences are explainable, the movement belongs to the environment and therefore to the user's handling. If they are outside that range, the shipping control is the place to look.
4. How to measure so the number counts
Use the oven-dry method as the reference. Sample, weigh, dry to constant mass, weigh again, calculate on dry mass, as set out in EN 322. It is the only method that can serve as an arbitration basis, because the process can be repeated and the result can be traced.
Keep samples away from edges and ends. Edges dry and absorb fastest and represent the panel least. Take at least three positions - top, middle and bottom of the stack - and two areas on the same panel.
A hand-held meter is useful, if you know where its bias comes from. These instruments are usually calibrated against the density and dielectric behaviour of solid wood. MDF differs in density, resin content and pore structure, so readings shift systematically. Their value is relative comparison: one instrument, one penetration depth, one measurement position, comparing points within a batch. Do not use the absolute reading to accept or reject a load.
Record the environment. Temperature, relative humidity and time of measurement. Moisture data without the climate it was taken in cannot be explained afterwards and cannot support a responsibility decision.
An arithmetic example. Moisture content is measured against dry mass, so a move from 6% to 9% means 3 kg of extra water per 100 kg of dry fibre. At a density of 720 kg/m³, one cubic metre of panel takes up roughly 21.6 kg of water. That water enters the fibre cell walls, and both thickness and length change - thickness usually more visibly, which is why moisture problems are often first reported as a thickness complaint.
5. After arrival, do not cut yet
A panel leaving a container moves from a marine climate with a daily temperature swing into a warehouse or workshop with a different climate. It needs time to settle, and how that time is handled decides whether the panel stays flat.
Unwrap first. Stretch film keeps water out at sea and keeps it in on land. Remove it on arrival and let the stack breathe.
Split the stack, use bearers, keep clear of walls. Leave aisles between stacks, use bearers tall enough for air movement underneath, and do not stand panels against a wall or directly on the floor. Floors and walls are the most consistent moisture source in any warehouse.
Stack flat or stand properly. Flat stacks need bearers close enough that no visible sag develops. Standing panels need a rack, a modest lean angle and evenly distributed support.
Re-test instead of counting days. Days are not the criterion; a stable reading is. Thin panels settle faster than thick ones, and a dry season is faster than a humid one. Watch for the difference between the two faces to converge.
Cut in sequence. Use the outer, settled panels first and leave the centre of the stack to continue stabilising. Pulling the core of a freshly unwrapped stack straight onto the line is the most common cause of "it moved after cutting".
6. Three clauses for the order
One: a moisture range and a decision rule. State the target range, the test method (EN 322 oven-dry), sampling positions and number of points, and the rule for acceptance - a mean across points plus upper and lower limits for single readings - together with the re-test and third-party arbitration route. A single number is not an agreement.
Two: packaging and transport requirements. Film and pallet specification, corner protectors and strapping, desiccant where the route and season call for it, and wood packaging treated and marked to ISPM 15. This clause decides how much water comes back.
Three: re-test on arrival and handling of out-of-range material. How many days after arrival the re-test is done, who tests, who pays, and whether out-of-range material is rejected, downgraded or compensated. Clear clauses keep a disagreement from becoming two monologues.
Clauses govern what happens after arrival. The upstream half of the question sits before the order: whether this factory can supply the board consistently at all, which rests on its records, its traceability and its packing discipline - see *Five Checks on a Panel Factory Visit*.
7. Conclusion
Moisture comes down to three sentences.
The press sets the process; the packaging sets the arrival. Stages one to four decide how dry the panel leaves; stages five to seven decide how dry it lands.
Bowing is about gradient, not average. The difference between two faces and between top and bottom of a stack carries more information than any single reading.
Acceptance is about method, not numbers. Moisture data with a sampling rule, a test method and an environmental record can support a decision. Without them, a number only supports an argument.

Figure 2: The EN 322 oven-dry sequence - sample, weigh, dry to constant mass, weigh again. The process repeats, which is what makes the result usable in arbitration.

Figure 3: Panels standing to stabilise after arrival, with air space between them. Stability is judged by whether readings converge, not by how many days have passed.
About WADA GROUP
WADA GROUP was established in 2010 and operates three factories in Xuzhou and Lianyungang, supported by overseas branches in Japan and Singapore. The company maintains an 18-person quality inspection team and an independent laboratory, holds EUDR, EPA, JAS, JIS, CARB P2 (EPA) and FSC certifications, and exports 100% of its output to more than 50 countries.
References
EN 322 *Wood-based panels - Determination of moisture content*.
EN 317 *Particleboards and fibreboards - Determination of swelling in thickness after immersion in water*.
EN 323 *Wood-based panels - Determination of density*.
EN 717-1 *Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method*.
ISPM 15 *Regulation of wood packaging material in international trade* (FAO International Standard for Phytosanitary Measures No. 15).
WADA GROUP. *Moisture-Resistant MDF: Choosing Between MDF.H and MDF.HLS*; *Nominal 18 mm MDF: Why Measured Thickness Differs*; *Why Edge Banding Fails on MDF*.
Editorial note
The relationship between moisture content and panel movement described here reflects the general behaviour of panel construction and processing and is presented to explain cause and effect. It is not a performance commitment for any specific product, batch or grade. Moisture targets, stabilisation time and packaging should be set against the destination climate, the transport route and the individual project, and agreed in the technical annex. Images are AI-generated illustrations containing no text or brand marks.